控箱是包含一個或多個低壓開關設備以及與之相關的控制、測量、信號、保護、調節等設備，并且由制造廠家負責用結構部件完整地組裝在一起的。

接線

1 接線順序

待一切準備妥當后，開始接線，根據原理圖，首先應完成主電路的接線，然后依次接控制電路及信號線路等。

2 放線

放線時必須根據實際需要長短來落料，活動線束應考慮最大極限位置需用長度，放線時盡量利用短、零線頭，以免浪費；二次導線不允許有中間接頭、強力拉伸導線及其絕緣被破壞的情況，導線排列應盡量減少彎曲和交叉，彎曲時對其彎曲半徑應不小于3倍的導線外徑，并彎成弧形，導線交叉時，則應少數導線跨越多根導線，細導線跨越粗導線為原則；布線時每根導線要拉勒挺直，行線做到平直整齊，式樣美觀；導線穿越金屬板孔時，必須在金屬板孔上套上合適的保護物，如橡皮護圈；導線束用阻燃纏繞管繞扎，為了達到導電時的散熱要求，纏繞管每繞一周應有3～10mm空隙，同時亦可分段纏繞，分段纏繞的間距為150～180mm，纏繞長度為100mm，分段纏繞的線束，分段亦應整齊，不允許參差不齊，導線應在行線槽內行走。

電線通過接線頭與接線及外部元件，然后合上斷路器，檢查每一路是否工作正常，只有全部的線路工作正常后才可以轉入下一道工序，測試完畢后，接線槽及接線端子蓋板應及時復位蓋上，電控箱內斷路器及空氣開關應保持在斷開狀態。